Acer B326HUL Manual do Utilizador

Acer LCD MonitorUser's Guide

Acer America Corporation 333 West San Carlos St., Suite 1500 San Jose, CA 95110, U. S. A. Tel : 254-298-4000 Fax : 254-298-4147 www.acer.co

1Special notes on LCD monitors iiiInformation for your safety and comfort iiiSafety instructions iiiCleaning your monitor iiiConnecting/disconnecting

1EnglishUnpackingPlease check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or

2ATTACHING/REMOVING THE BASEATTACHING/REMOVING THE BASEATTACHING/REMOVING THE BASEATTACHING/REMOVING THE BASEATTACHING/REMOVING THE BASEInst

3SCREEN POSITION ADJUSTMENTSCREEN POSITION ADJUSTMENTSCREEN POSITION ADJUSTMENTSCREEN POSITION ADJUSTMENTSCREEN POSITION ADJUSTMENTIn oder t

4•••leviwS leviwSleviwS leviwSSwivelWith the built-in pedestal, you can swivel the monitor for the mostcomfortable viewing angle.MREnglishBa o6060

5EnglishConnecting the power cord• Check first to make sure that the power cord you use is the correct type required for your area.• The monitor has a

6EnglishConnector pin assignment19-pin Color Display Signal Cable** only for certain modelsPIN No. Description PIN No. Description1 TMDS Data2+ 2 TMDS

7English24-pin color display signal cable*PIN No. Description PIN No. Description1 TMDS data 2- 13 NC2 TMDS data 2+ 14 +5 V power3 TMDS data 2/4 shiel

Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such cha

8EnglishStandard timing table1VGA 640x480 60 Hz2VGA 640x480 75 Hz3VESA 720x400 70 Hz4SVGA 800x600 60 Hz5SVGA 800x600 75 Hz6XGA 1024x768 60 Hz7XGA 1024

9EnglishInstallationTo install the monitor on your host system, please follow the steps below:Steps 1 Connect the video cablea Make sure both the moni

EN-14MainMenuiconSubMenuiconSubMenuitemDescriptionN/AUser modeUser defined. Settings can be fine-tuned tosuit any situationN/A N/AStandardmodeDefault

EN-15Adjusting the OSD settings--------------------------------------------------------------------Note: The following content is for general referenc

EN-16Adjusting the OSD position1Press the MENU key to bring up the OSD.2Using the directional keys, select OSD from the on screen display.Then naviga

4 Select Power-off USB charge ON/OFF to enable/disable Power-off USB charge function. /

EN-18Product information1Press the MENU key to bring up the OSD.2Using the / keys, select Information from the OSD. Then thebasic information of

TroubleshootingBefore sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.

iiiSpecial notes on LCD monitorsThe following are normal with the LCD monitor and do not indicate a problem.•Due to the nature of the fluorescent ligh

ivAccessibilityBe sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possi

vampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total ratin

viNote: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage an

viiDisposal instructionsDo not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the

viiiThis product has been shipped enabled for power management:•Activate display’s Sleep mode within 15 minutes of user inactivity.•Activate computer’

ixTaking care of your visionLong viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, v